About the Script
Countdown Intervalometer is an easy to use intervalometer script for CHDK. This script should work with most Canon cameras that run CHDK. Special care was taken to avoid using PROPCASE features that would cause compatibility problems with some cameras. This script was created by Andrew Hazelden.
Note: If you want to record longer timelapse sequences with your Canon Powershot camera you should look into getting an external wall power module. It is also possible to buy / make a larger external battery pack that will power your camera for days.
Steps to Load the Script
1. Copy the file counter.bas to your CHDK/SCRIPTS folder on your SD memory card.
2. Turn on your camera.
3. Load up the CHDK menu and then select Scripting parameters.
4. In the Script Menu open the uBASIC script counter.bas by selecting Load script from file…
5. Set the parameters for your time-lapse in the script menu.
6. Close the CHDK menus. With ALT mode active press the shutter button to start running the script. After the first photo is taken, the estimated time remaining will be displayed.
7. To stop running the script press the shutter button again then turn off ALT mode.
When the script finishes you will see the following printed on the display:
Sequence Completed 10 Shots Taken in: 00:01:07 HH:MM:SS *** FINISHED *** Countdown Intervalometer>
In the CHDK Script menu there are two parameters you can change. The first is Interval in Sec and the second is Number of Shots. If you want to take pictures forever, or until your memory card is full set Number of Shots to zero.
If you want to take pictures as fast as possible set the camera to continuous photo mode and set the Interval in Sec parameter to zero.
Countdown Intervalometer Screenshots
Version 1.0 - Created Sept 16, 2010.
- Original script released on CHDK forum by Andrew Hazelden.
Version 1.1- Created Sept 19, 2010.
- Added the perpetual intervalometer mode.
Download the Countdown Intervalometer script: CHDK_Countdown_Intervalometer.zip
You can join the discussion on the Countdown Intervalometer script on the developer's Countdown Intervalometer blog page.
Source Code - counter.bas
rem Countdown Intervalometer v1.1 rem An intervalometer script that will take a specific number of photos. rem rem If the Number of Shots is set to zero the intervalometer switches from rem a countdown intervalometer mode over to a perpetual intervalometer mode rem that will continue to take photos until your memory card is full or your rem camera's battery runs out of power. rem rem Version 1.1 updated Sept 19, 2010. rem Added the perpetual intervalometer mode. rem rem Version 1.0 Created by Andrew Hazelden on Sept 16, 2010. rem rem E-mail: firstname.lastname@example.org Blog: www.andrewhazelden.com rem rem To download the latest version check out this blog post: rem http://www.andrewhazelden.com/blog/2010/09/ubasic-countdown-intervalometer-script-for-canon-powershots-running-chdk/ @title Countdown Intervalometer rem i is the interval between photos in seconds. @param i Interval in Sec @default i 10 rem n is the number of shots to take. @param n Number of Shots @default n 99 rem e is elapsed photos taken. e=0 rem r is the number of shots remaining. r=n rem get timelapse start time in ms z=get_tick_count rem q is photo time elapsed temp counter in ms rem v is actual time per photo in ms rem check for perpetual photo mode if Number of Shots equals zero. if n=0 then gosub "perpetual" if n>0 then gosub "countdown" rem get end time using x=get_tick_count rem calculate total timelapse duration p = (x-z)/1000 rem print total timelapse duration rem s is seconds elapsed s=(p)%60 rem m is minutes elapsed m=((p)/60)%60 rem h is hours elapsed h=(p)/3600 cls print "Sequence Complete." print e, "Shots Taken in:" print h;":";m;":";s, "HH:MM:SS" end :remaining rem time remaining subroutine rem s is seconds remaining s=((v/1000)*r)%60 rem m is minutes remaining m=(((v/1000)*r)/60)%60 rem h is hours remaining h=((v/1000)*r)/3600 print "Est. Time Remaining:" print h;":";m;":";s, "HH:MM:SS" return :perpetual rem perpertual intervalometer mode rem run the while loop forever. while 1 shoot rem increase elapsed photo counter e=e+1 cls print "Shot:", e rem interval between photos delay sleep i*1000 wend return :countdown rem countdown intervalometer mode rem run the while loop until there are no shots remaining. while r rem get the start time for this shot q = get_tick_count shoot rem increase elapsed photo counter e=e+1 rem decrease shots remaining counter r=r-1 cls print "Shot:", e, " of ", n rem If we are beyond the 1st shot call the "remaining" subroutine rem to display the time remaining. if e>1 then gosub "remaining" rem interval between photos delay if r>0 then sleep i*1000 rem calculate time between photos in ms v=get_tick_count-q wend return