Wikia

CHDK Wiki

Compiling CHDK under Linux

Talk5
565pages on
this wiki
Revision as of 15:46, September 25, 2013 by Andyhull (Talk | contribs)

This is the procedure I used to compile CHDK (April 2007). Look for the shorter alternative procedure at the end of this page.

June 2007. I have modified the procedure to use gcc-3.4.6 and Vitaly's patch in place of gcc-4.1.2. The reason for the change is that there is an issue with 'endianness' and floating point numbers that is addressed by Vitaly's patch.

I compiled the CHDK with gcc-4.1.2, both 'trunk' and 'grand' branches, with success since April until I met a problem using the 'pow' function under 'trunk'. The 'grand' branch addresses the issue differently and the floating point code worked fine under the 'grand' branch when compiled with gcc-4.1.2.

There is a 'minor' difference of behavior between the two compilers. With gcc-4.1.2, the variable __arm__ is defined even when the compiler is called with option -mtumb; with gcc-3.4.6 and the patch and option -mthumb, the variable __arm__ is not defined but variable __thumb__ is. The CHDK file 'include/lowlevel.h' is sensitive to that difference of behavior.

The reason I used gcc-4.1.2 in the first place is that I was not aware of Vitaly's patch.

Getting the source

Notice

CHDK source was split into two main streams effective Dec 26,2011. A stable stream was created as a branch and the main trunk became the development or unstable stream. References on this page are to the development or unstable stream. Change https://tools.assembla.com/svn/chdk to https://tools.assembla.com/svn/chdk/branches/release-1_0 to use the stable stream.

  • Create a directory where to load the CHDK source code.
 > mkdir ~/chdk && cd ~/chdk
  • Get the CHDK source code.
 > svn co https://tools.assembla.com/svn/chdk/trunk chdk
  • and update the source code every now and then:
 > cd chdk && svn up

Installing the cross compiler

Attention

There are alternate guides for setting up newer cross compilers here: gcc433 and here gcc452


Get the sources of gcc and binutils from a GNU repository. Decide where the cross compiler will be on your computer.

 > mkdir ~/arm-elf
Tell your computer you are going to run programs from that location.
 > export PATH=${HOME}/arm-elf/bin:$PATH
Create a working area and build binutils and gcc.
 > mkdir ~/wa
 > cd ~/wa
 > tar xvfj ~/src/binutils-2.17.tar.bz2
 > tar xvfj ~/src/gcc-3.4.6.tar.bz2

Note: About using the latest Gcc-4.3.3 take a look at this article.

 > cd binutils-2.17
 > ./configure --srcdir=../binutils-2.17 --target=arm-elf \
     --prefix=${HOME}/arm-elf --disable-werror
 > make
 > make install
 > cd ..
Apply Vitaly's patch to the compiler.
 > (cd gcc-3.4.6 && patch -p0 <~/chdk/tools/patches/gcc-3.4-arm.diff)
 > mkdir gcc-3.4.6-arm-elf && cd gcc-3.4.6-arm-elf
 > ../gcc-3.4.6/configure --srcdir=../gcc-3.4.6 --target=arm-elf \
    --enable-multilib --enable-languages=c --enable-clocale=gnu \
    --disable-libm --disable-libc --disable-threads \
    --disable-nls --disable-libssp --disable-intl --disable-libiberty \
    --with-cpu=arm9 --with-newlib --prefix=${HOME}/arm-elf
 > (unset LIBRARY_PATH; unset CFLAGS; make && make install)
That's it for the installation of the cross-compiler.

Compiling the CHDK.

Go to either 'trunk' or 'grand'.

 > cd ~/chdk/grand
Manually edit file <makefile.inc> to select PLATFORM and PLATFORMSUB for your camera: just remove the "#" comment characters. Also, add the following line at the beginning of file <makefile.inc> to tell CHDK where the arm cross compiler is,
 export PATH=${HOME}/arm-elf/bin:${PATH}
You should be ready to compile everything.
 > make fir
The results are left in the "bin" directory.
If you want to compile firmware for an another camera, just execute make with PLATFORM and PLATFORMSUB arguments. For example:
 > make PLATFORM=a620 PLATFORMSUB=100f fir
Before compiling firmware for a different camera, the build directory may need to be cleaned. For example:
 > make PLATFORM=a620 PLATFORMSUB=100f clean
To compile firmware for all cameras just type:
 > make batch-zip

Alternative cross compilers.

Compiling CHDK on Ubuntu

See this forum thread : Compiling CHDK on Ubuntu 11.10

An alternative method with gcc-3.4.6

There is a patch included in CHDK for building with gcc-3.4.6. It's a simpler install if you want to use this version of gcc. This method uses a global install of the arm-elf tools.

Remember to clear any CFLAGS you've got set:

 > export CFLAGS=""

Compile and install binutils

Extract the source, change to its directory, and

 > mkdir binutils-2.17-arm-elf
 > cd binutils-2.17-arm-elf/
 > ../configure --srcdir=../ --target=arm-elf && make && sudo make install

Compile and install GCC-3.4.6

Download gcc-3.4.6, extract it and change to that directory. Patch the GCC source with the toolkit patch:

 > patch -p0 < [path_to_chdk]/tools/patches/gcc-3.4-arm.diff
Build the source:
 > mkdir gcc-arm-elf
 > cd gcc-arm-elf/ 
 > ../configure --srcdir=../ --target=arm-elf --with-cpu=arm9 \
   --with-newlib --enable-multilib  --enable-languages=c \
   && make && sudo make install

You can now build the CHDK source as directed above

Compile and install GCC-4.5.2

(Updated 24th Sept 2013) Here is a script to build the tool chain needed for building CHDK based on GCC 4.5.2.

Create a suitable folder to build GCC with something like mkdir ~/build-dir and save the script to this folder.

MPFR version 3.0.0 is no longer the current version, therefore you will need edit the script and change the following line...

wget -c http://www.mpfr.org/mpfr-current/$MPFR.tar.bz2

to

wget -c http://www.mpfr.org/mpfr-3.0.0/$MPFR.tar.bz2

Dont forget to chmod the script o+x so you can run it.

If you encounter any issues with the script, don't forget to post any fixes here.

After building the tool chain you can now download and build CHDK:

> export PATH=${HOME}/build-dir/arm/toolchain/bin:${PATH}
> svn co https://tools.assembla.com/svn/chdk/trunk chdk
> cd chdk
> make PLATFORM=sx200is PLATFORMSUB=100c fir

You may need to adjust the PATH to match the build folder you created above and the platform variable in last line to the model of your camera. The ./bin/DISKBOOT.BIN need to be copied to your SD card. If you want a PS.FI2 for auto booting, you need to follow ./platform/fi2.inc.txt to get ./bin/PS.FI2 after building CHDK.

Note: If you have pre-existing cross compilers (for example if you have been coding for your raspberry pi), you might need to alter you PATH variable to exclude the related paths (anything like /home/blah/sandbox/raspian/raspberrypi/tools/arm-bcm2708/gcc-linaro-arm-linux-gnueabihf-raspbian/bin ) before you attempt to install GCC with the above script, otherwise you may end up with some very strange results.

The Gentoo way

Gentoo Linux contains a nice utility to automate this process. Emerge sys-devel/crossdev and run

crossdev -t arm-elf -s1 --without-headers --binutils 2.18-r4

This commands should compile and merge the latest gcc and binutils 2.18 (the latest binutils-2.19.1 doesn't work with chdk). Look at the versions at $PORTDIR_OVERLAY/cross-arm-elf/binutils/
The first line in makefile.inc should look then like this:

PATH := /usr/i686-pc-linux-gnu/arm-elf/binutils-bin/2.18/:/usr/i686-pc-linux-gnu/arm-elf/gcc-bin/4.4.1/:${PATH}

GCC 4.x

Notice

A gcc 4.3.1-binutils 2.18 environment kit for Linux was available from here: chdhdev drop but the link is dead
This is the environment running on the CHDK autobuild server (19-Jan-2009), it's compiled under debian etch


Well, this works fine on Ubuntu 8.04.2. About using the latest Gcc-4.3.3 take a look at this article.

Success reports

- binutils-2.22 and gcc-4.5.3 on Gentoo ~amd64 (using sys-devel/crossdev)

- binutils-2.23 and gcc-4.5.4 gcc-4.6.3 gcc-4.7.2 (latest needs --enable-obsolete to allow arm-elf binary format) OpenSUSE amd64

Python GUI

Notice

An GUI written in python is available here for download


cd directory/where/compiler/is
python chdk_linux_compiling_gui.py

The rest should be self-explaining.

More info can be found in the german forum:

http://forum.chdk-treff.de/viewtopic.php?f=1&t=1829

Use google translate if you can't read german.

Advertisement | Your ad here

Around Wikia's network

Random Wiki